Central® 高密度聚乙烯曝氣管
High Density Polyethylene (HDPE) Porous Tube is a durable solution for fine pore diffusion of air and other gases. Each tube is designed to fit standard Schedule 40 PVC end fittings and couplings. The omni-directional porous structure is excellent for diffusing, sparging, and aeration applications, emitting a multitude of small, evenly distributed bubbles.
Polyethylene

應用:
  • 都市和工業廢水處理
  • 水產養殖 (養殖池塘,活魚卡車,等等.)
  • 電鍍液空氣攪拌
  • 泡沫清潔劑
  • 食品加工的空氣攪拌
  • 泡沫清潔劑
產品特性:
  • 管體本身具有質輕、堅韌、耐酸鹼、不腐蝕、不易破裂等特性
  • 全向多孔結構提供氣泡均勻分散全管
  • 與 Sch. 40 PVC 管件相容、安裝簡便
  • 耐磨損、抗化學性
  • 材料符合美國聯邦條例 CFR, Title 21, Section 177.1 520 Item 2.1, 與食物接觸法規
產品規格:
型號 管尺寸 (Sch40) 接頭尺寸 (PVC) 管 外徑 管 內徑 孔徑 背壓*
HPT-D50 1/2" 13mm 7.5mm 30" 910mm 20-40 µm ≤ 28cm
HPT-D75 3/4" 20mm 11mm 30" 910mm 20-40 µm ≤ 28cm
HPT-050 1/2" 1/2" 0.840" 21mm 0.618" 16mm 48" 1210mm 20-40 µm ≤ 28cm
HPT-075 3/4" 3/4" 1.05" 26mm 0.810" 20mm 48" 1210mm 20-40 µm ≤ 20cm
HPT-100 1" 1" 1.29" 32mm 0.960" 24mm 48" 1210mm 20-40 µm ≤ 25cm
HPT-200 2" 2" 2.4" 60mm 1.87" 47.5mm 48" 1210mm 20-40 µm ≤ 20cm
* Centimeters of H2O at 12,000ml/minute of air per 1 inch tube


水中曝氣情形:

Polyethylene

HPT-50接口應用:
準備1/2"灣頭牙管(直管也可以),銅頭及止漏防水膠帶,
將止漏防水膠帶沿接口圈4~5圈,再將灣管直接套上即可。
銅頭可依自己需求選購口徑大小。

Pht-50

接口完成圖:成如下圖

hpt-50

加工技術:

  • Cutting, Turning, and Drilling Conventional band, table, and hand saws may be utilized as well as lathes and drills.
  • Thread Cutting External or internal threads can be cut using standard metal cutting tools, either on a lathe or by hand. A stronger thread can be achieved by dipping the area to be threaded into PVC pipe cement and allowing it to harden before cutting the threads.
  • Bonding and Sealing Tubes can be bonded to fittings and couplings using hot melt adhesives, PVC plastic pipe cement, epoxy, or similar sealants. These adesives form a strong mechanical bond by curing on the surface and within the pore structure of the tube

Characteristic多孔高密度聚乙烯塑料的特性:

Throughout all HDPE porous plastic runs an intricate network of opencelled, onmi-directional pores. These pores, which can be made in average pore sizes down to one micron, give porous plastics their unique combination of filtering capability and structural strength.

Unlike the direct passages in woven synthetic materials and metal screens, the pores in porous plastic join to form many tortuous paths giving porous plastics a dual filtering capability. Not only do they act as surface filters by trapping particles large than their average pore size, they also trap much smaller particulate matter deep in their complex channels for a "depth filter" effect. This tortuous path structure is so efficient that, as a rule of thumb, with an average pore size of 25 microns, offer you approximately the same filtration as many five micron-rated filters

HDPE can be used in continuous service at temperatures up to 180°F (82°C) and intermittently at 240°F (116°C). If not stressed, it is stable at 212°F (100°C) in continuous service.

HDPE Porous Plastics are naturally hydrophobic, but aqueous solutions can be forced through under pressure. The material is cleanable with HCI (muriatic acid) or chlorine

Not recommended in presence of strong oxidizing acids, prolonged fire and sunlight and solvents above 176°F (80°C).